Your Location：Home > News > Industry news 
Several common problems of bag-making machine and countermeasures.
Category：Industry news Publish：2018-04-11 10:59:51 View：1029次
[Back]
Bag-making machine is a machine that makes various kinds of plastic packaging or other material packaging bags, and its processing range is the packaging bags of different kinds of plastic or other materials with different thickness and thickness. Of course, there are a lot of problems during the use of the bag making machine, which is to help you to clear the troubles of the bag-making machine.
1. How to cut the cold cutting knife of the flat mouth machine?
When the cold cutting knife is always cut constantly, it is necessary to check whether the cutting tool is sharp or not. Check whether the balance of the upper and lower knife is suitable, the knife slide is used for a long time, and the wear gap will cause the knife imbalance.
2. Cutting three or more of the machine, how about the size of the bag?
After that thin film, the rubber roller is covered with a layer, which can be even with other materials.
3. What caused the spring break of the flat mouth machine?
The self-adhesive strips are not put in place, and the spring will be broken when the spring is up and the spring will be broken, and the self-adhesive tape must be adhered to in operation. There is also a reason, the material is not neat or a tuo into the rubber roller, causing the spring to fail.
4. How about the difference between the sealing sides of the bag making machine?
It is necessary to adjust the aluminum rollers to the edge of the sealing side to avoid this situation.
5. What is the reason why the edge sealing machine is often glued to the conveyor belt?
The self-adhesive tape is misaligned and adhered to the conveyor belt. It is necessary to adjust the self-adhesive position of the trailing edge straightener, and put it in the self-adhesive position to prevent the running.
6. What is the reason that the edge of the cut OPP has the edge or explosion?
The hot knife and the suction arm are not adjusted. The normal condition is that the hot knife cuts up to 2 cm, and then the suction arm is sent out again.
7. How about the length of the finished product?
The pressure spring is not pressed tightly, which causes the roller to slip, or the splint in the back is too tight, which needs to be adjusted.
8. What do you do with the blocking machine in front of the cold cutting knife?
This should be the case that the bag is too electronic, using a rubber band to attach a small piece of paper to the screw on the knife beam, and cut out the tape at the same time.
9. The thickness of the film blowing machine is uneven, how about thin?
You need to wrap around the thin side of the rack until it fits.
10. The printing bag is not smooth, and the electric eye is not sensitive enough.
First check whether the electric eye is used correctly, the electric eye has a certain attention to the color sensitive reaction, if the bag is monochrome with blue, heavy color is red, red can be used in monochrome, heavy color. The roller under the eye of the straightening machine should be sprayed with black. If the bag is single and heavy, it will be the best in white.
11. How long does the new machine not cut the bag, cut the knife repeatedly thin film, or one place cut repeatedly?
In this case, it may be that after a period of time, the sliding block of the upper blade is too large for the gap between the sliding block and the copper plate, thus causing the cutting edge to be cut continuously. You can adjust the top seam (M6 interior Angle) of the copper piece, and adjust it to the handle without moving the blade, but not too tight. When the machine is started to cut 15-20 pieces per minute, there is no obvious jitter between the upper knife beam and the clearance is just right. In addition, can adjust the spring pressure of the knife beam.
12. What should I do if the sealing machine and R machine are not strong?
Check whether the hot knife has carton: the hot knife seal is not smooth, and the sealing is sometimes firm, sometimes not strong.
Check to see if the blade is deformed and bent by heating. The test method is to turn the hot knife to the bottom, when the hot knife is just about to be connected.
When touching the silicone roller or silica gel plate, it is used to determine whether the hot knife is bent, if bending, to repair the plane of the blade.
(3) check whether film electronics is too strong, with no smoke a pack of electronic film test, a sealing and cutting the look of the sealing have obvious changes, if yes, proved that the roll of film electronics is too strong, suggested in a coil.
Quanzhou xiutai plastic machinery co., LTD., since its establishment for many years, adhering to the unwearying, realistic and innovative culture; Taking science and technology as the forerunner, with precise and rigorous manufacturing idea as the foundation; We have developed a series of plastic blown film equipment with unique structure, superior performance and excellent quality.
We have a group of skilled technicians who are proficient in plastic processing technology and have rich experience in mechanical design. Unique machine design, careful production, easy to operate, products sell well in the domestic market, exported to all over the world.
Association's molding machine always adhere to the "honesty, mutual benefit, common development" principle, adhere to "quality first, customer first" belief, and constantly improve the internal management system and after-sales service system, wholeheartedly for the majority of users provide blown film industry professional solutions.
1. How to cut the cold cutting knife of the flat mouth machine?
When the cold cutting knife is always cut constantly, it is necessary to check whether the cutting tool is sharp or not. Check whether the balance of the upper and lower knife is suitable, the knife slide is used for a long time, and the wear gap will cause the knife imbalance.
2. Cutting three or more of the machine, how about the size of the bag?
After that thin film, the rubber roller is covered with a layer, which can be even with other materials.
3. What caused the spring break of the flat mouth machine?
The self-adhesive strips are not put in place, and the spring will be broken when the spring is up and the spring will be broken, and the self-adhesive tape must be adhered to in operation. There is also a reason, the material is not neat or a tuo into the rubber roller, causing the spring to fail.
4. How about the difference between the sealing sides of the bag making machine?
It is necessary to adjust the aluminum rollers to the edge of the sealing side to avoid this situation.
5. What is the reason why the edge sealing machine is often glued to the conveyor belt?
The self-adhesive tape is misaligned and adhered to the conveyor belt. It is necessary to adjust the self-adhesive position of the trailing edge straightener, and put it in the self-adhesive position to prevent the running.
6. What is the reason that the edge of the cut OPP has the edge or explosion?
The hot knife and the suction arm are not adjusted. The normal condition is that the hot knife cuts up to 2 cm, and then the suction arm is sent out again.
7. How about the length of the finished product?
The pressure spring is not pressed tightly, which causes the roller to slip, or the splint in the back is too tight, which needs to be adjusted.
8. What do you do with the blocking machine in front of the cold cutting knife?
This should be the case that the bag is too electronic, using a rubber band to attach a small piece of paper to the screw on the knife beam, and cut out the tape at the same time.
9. The thickness of the film blowing machine is uneven, how about thin?
You need to wrap around the thin side of the rack until it fits.
10. The printing bag is not smooth, and the electric eye is not sensitive enough.
First check whether the electric eye is used correctly, the electric eye has a certain attention to the color sensitive reaction, if the bag is monochrome with blue, heavy color is red, red can be used in monochrome, heavy color. The roller under the eye of the straightening machine should be sprayed with black. If the bag is single and heavy, it will be the best in white.
11. How long does the new machine not cut the bag, cut the knife repeatedly thin film, or one place cut repeatedly?
In this case, it may be that after a period of time, the sliding block of the upper blade is too large for the gap between the sliding block and the copper plate, thus causing the cutting edge to be cut continuously. You can adjust the top seam (M6 interior Angle) of the copper piece, and adjust it to the handle without moving the blade, but not too tight. When the machine is started to cut 15-20 pieces per minute, there is no obvious jitter between the upper knife beam and the clearance is just right. In addition, can adjust the spring pressure of the knife beam.
12. What should I do if the sealing machine and R machine are not strong?
Check whether the hot knife has carton: the hot knife seal is not smooth, and the sealing is sometimes firm, sometimes not strong.
Check to see if the blade is deformed and bent by heating. The test method is to turn the hot knife to the bottom, when the hot knife is just about to be connected.
When touching the silicone roller or silica gel plate, it is used to determine whether the hot knife is bent, if bending, to repair the plane of the blade.
(3) check whether film electronics is too strong, with no smoke a pack of electronic film test, a sealing and cutting the look of the sealing have obvious changes, if yes, proved that the roll of film electronics is too strong, suggested in a coil.
Quanzhou xiutai plastic machinery co., LTD., since its establishment for many years, adhering to the unwearying, realistic and innovative culture; Taking science and technology as the forerunner, with precise and rigorous manufacturing idea as the foundation; We have developed a series of plastic blown film equipment with unique structure, superior performance and excellent quality.
We have a group of skilled technicians who are proficient in plastic processing technology and have rich experience in mechanical design. Unique machine design, careful production, easy to operate, products sell well in the domestic market, exported to all over the world.
Association's molding machine always adhere to the "honesty, mutual benefit, common development" principle, adhere to "quality first, customer first" belief, and constantly improve the internal management system and after-sales service system, wholeheartedly for the majority of users provide blown film industry professional solutions.
